Hello,

Soon after the onset of winter, some strong wind storms and temperatures below freezing in the morning, the actuator started moving the dish very slowly as observed from the VBox II numeric display, for about the last week. Went down to the...

Hello,

I have a 24 inch actuator arm that may be used eventually for a 4 foot C/Ku band offset dish. If the 36 inch actuator moving our 10 foot dish dies eventually, can this 24 inch actuator be used? Both were purchased from tek2000. Any...

Boy, trying to find a 36v 24 reed sensor actuator arm is like trying to find a needle in a haystack. The Tek2000 site has none in stock for 12 dishes, i.e., heavy duty.

Any idea where I can find one? The one I have is going south. I dare not try...

Hello,

I am concerned that my actuator shaft seems to be laboring, loud?, and in need of some lubrication perhaps? I have been spraying the shaft with silicone spray. I noticed that there is a small hole near the top of the shaft sleeve pictured...

Hello,

This morning my super jack stopped working. I went down and manually spun the retractable arm which eventually moved without rotating, which was unexpected. I attempted to repeak the dish on zenith, and listened to the actuator move....

Hello,

After replacing my actuator with a brand new one, we decided to try the snake on the actuator to provide extra protection from the elements. It was soon evident that the snake was restricting the actuator arm's movement, and appeared to be...

Hello,

I am about to re-position the super jack (that moves our 10 foot dish) such that we will be able to get over to 65W, even if it means losing 139W. I attempted to move the dish from 87W to 85W, and the actuator would not move. I went down to...

Hello good night, a few weeks ago I bought an Actuator Motor Housing (Heavy Duty) in the tek2000 store as a substitute for my mechanical arm that is still in good condition and which I show you my doubt is that I bought a Heavy Duty engine (2.0 inch...

I've had an 18 heavy duty actuator bought from Tek2000 for about a year.
Has been working well however it has suddenly got stuck at a fully retracted position.

When power is applied, it rotates but doesn't extend an inch..
Please help tek2000

Could someone help me and tell me how to connect my actuator to Monterey 100c Plus?

I attach images

Hello,

Recently, my diseq box stopped recognizing its positions, after my dish was blown off axis by wind gusts. A quick reset to clarke belt zenith, however the diseq still would not recognize the positions that had been saved off, throwing an...

I scanned 131W. Noticed I wasn't getting some transponders showing in Dreamset. A friend suggested I bump the dish a few clicks and watch in signal finder . Sure enough, a few clicks and the transponders that were weak peaked to match the strong...

When installing dish support on post(10 ft dish, post exactly plumb) I was setting declination and noticed dish swivel assembly had an offset axis, in relation to post which is plumb. It seems to be about 6 deg. Is this proper, or was there a...

Where does one buy power cable for dish controller ? Is the coax and power cable all in one, or do we run separate cables. Have 100 ft from dish to receiver.
Tks for any help
Sam

All,

Some new products are currently available and coming soon to facilitate multi-axis motorization and control of the dish you purchase from us or one of our affiliates. Our 6th generation (and beyond) antennas have been fabricated to accept the...

Hi all,

Has anyone out there been able to utilize USALS with a C band dish screw jack ?

Is there a C band screw jack dish mover that operates on USALS commercially
available ?

I have a Stab HH 90 on my 90 cm geosatpro running USALS from my...

I'm about to turn my stationary 100cm fortec to motorized system, the motor arrives soon. An HH motor SG2100 by Moteck. I've reviewed various installation guides but my dish does not have the specialized mounting hole for the motor I seen some...

I picked up a really nice AJAK 180 H to H motor recently and am making plans to put it to use next year. I have not found much info about it online so any documents or know how would be greatly appreciated! My dream is to set it up on a 12 footer...

Hi Folks,

Long time user of C-band satellite technology.

My one complaint is that high winds will occasionally move the dish a bit east or west along the arc which requires resynching the positioner. Is there any technology available that...

Anyone sell HH motors for C-Band?