bit drill size for the 8 solid dish mast
bit drill size for the 8 solid dish mast
any one know this size to put the mast the box come with 3 big but no idea the size to drill the hole i do not want to make mistake
-
- TVRO Guru
- Articles: 0
- Posts: 217
- Joined: Wed Oct 11, 2017 6:05 pm
- Has thanked: 3 times
- Been thanked: 29 times
Re: bit drill size for the 8 solid dish mast
Just match the diameter of your bolt to the drill bit and go for it. Drill it to that size and the anchor probably won't tap in. Then try one size larger until the hole is big enough to pound in the anchor. Trial and error. Just drill small and go up in increments until the anchor will fit. If you start small and go up you won't screw it up.
10' Tek C-band dish, 1.2 meter KU band dish, ASC1 mover, Octagon/Zgemma/Edison dual band STB's. Running OpenPli on all.
Re: bit drill size for the 8 solid dish mast
than you sir but this 3 bolds come with the 8 feet solid dish from tek 2000 , shut be exactly the drill bit size to used in the instruction and is not there, i to confuse right now , i star saving to buy one tube to put in the patio grass with cement, i believe that is more easy to do it but i s another problem the one the boss sale is 3.5 inch for the 8 feet solid , do my dish will fix inside because the one come in the box is 4.5 inch. ?
- tek2000
- TVRO Salesman / Sponsor
- Articles: 0
- Posts: 329
- Joined: Fri Jun 20, 2014 4:38 am
- Location: Canada
- Been thanked: 11 times
- Contact:
Re: bit drill size for the 8 solid dish mast
Use 3/4" concrete/masonry drill bit. Just to be sure, take the anchor to the hardware store and make sure the anchor sleeve and drill bit you purchase are exactly the same size.
Owner
http://www.tek2000.com
#1 Supplier of TVRO Satellite Equipment in North America
[email protected]
(I am not on this forum often and don't check forum PMs, so please email me for faster service)
http://www.tek2000.com
#1 Supplier of TVRO Satellite Equipment in North America
[email protected]
(I am not on this forum often and don't check forum PMs, so please email me for faster service)
Re: bit drill size for the 8 solid dish mast
boss i go in to home depot let see ,if no i goin to buy one from you to put in soil but iam confuse if the 3.5 inch pole will fix my solid dish
- fatso
- TVRO Guru
- Articles: 0
- Posts: 1368
- Joined: Wed Aug 13, 2014 7:46 pm
- Has thanked: 16 times
- Been thanked: 197 times
Re: bit drill size for the 8 solid dish mast
I think the 8' solid from Tek takes a 4.5" O.D. pole, so get one of those. In the old days the tvro industry exclusively used 3.5" O.D. poles for consumer tvros up to 12' but that was a mistake. Under high wind loads the mount can rotate on a smaller pole or the pole itself may bend. Steel was expensive in those days so people cut corners a lot.
12ft Mesh Dish
C-Band Enthusiast since 1983
C-Band Enthusiast since 1983
Re: bit drill size for the 8 solid dish mast
in the site of the pole for sale 3.5 said is for 8 feet i guess mister tek has to clear this . and yesthe one come in the box is 4.5
Re: bit drill size for the 8 solid dish mast
OYE guys i need another help i am try in to do tuning up in my inclination any one know where is the polar axis in my back of muy dish, to put the inclinometer is 8 feet from tek solid any help i really appreciate . please point in my picture, gracias